Lamp - Carrying

If you are an avid car enthusiast or a jack of all trades, then you certainly have a garage or a suitable shed. It is in these areas that the main need for work is the lamp - carrying: there is always a place that is difficult to access for table and wall lamps, or small parts that require a concentrated beam of bright light. Lamp - carrying can easily be done from the available throwing material with your own hands. A little patience and half an hour of time - that's all you need to create this homemade! Materials for work: • A cord (for example, from an old vacuum cleaner) with a working plug at one end - 1 pc .;• Suspension lamp holder for the lamp - 1 pc; • Empty foam cylinder from the mounting foam - 1 pc; • Chandelier body with a horn (without a plafond) - 1 pc; • Short bolt 3 pieces; • Nut - 3 pieces; • Drill, thin drill bit, screwdriver. Stages of work execution: The first stage: we bring wires. We release the old chandelier from the plafond.
Lamp carrying
Find the wire from unused household appliances (in the present embodiment, the cord from the vacuum cleaner is used).It is desirable: the wire is longer, with a double insulating layer, so that it has a working plug at one end.
 Carrying Lamp
Unscrew the horn from the body. We thread the cord into it so that the direction of movement goes towards the connection of the horn with the canopy.
 Carrying lamp
The second stage: connect the wires. We are looking for a lamp holder for the lamp.
Carrying lamp
We disassemble it into its components: disconnect the body and the threaded sleeve, remove the porcelain liner.
Carrying lamp
Drawn out of a horn free the end of the cord from the outer insulation, we clean the wires themselves (by cutting and removing the inner insulating layer from both wires).
 Carrying Lamp
>img src="https://sdelaysam-svoimirukami.ru/images/14/612-lampa-perenoska.jpg" alt="Carry lamp" title="Carry lamp">
We put chandeliers into the body stripped wires.
Lamp carrying
Further work is carried out inside the luster case.First we insert the wires into the body of the cartridge.
Carrying lamp
Fixing it with a special nut that secures the chandelier's horn to the body.
Carry Lamp
 Carry lamp
Next step: connecting the wires to the porcelain insert of the cartridge.
Carrying lamp
To do this, twist a loop at the end of each wire.
 Carrying lamp
Unscrew the contact screws on the porcelain liner. We put on a cog in a loop. We put the screw in place and fasten it tightly to the insert (the wire ring remains under the screw on the insert).
 Carrying Lamp
After twisting the contact screws, we place the porcelain liner into the body of the cartridge (wires inside).
Carrying lamp
 Carrying Lamp
Connecting cartridge case with threaded sleeve. Carrying lamp
The third stage: we make a reflector. To concentrate the direction of the light, we make a “curtain” - a reflector, cutting the spade-like detail out of an empty foam container.
 Carrying Lamp
Lamp carrying
From one end of the reflector we drill a hole with a thin drill, trying to combine them with the holes on the chandelier body - in places of fixing the plafond (in the presented version of the holes three pieces - in the center and the edges). Carrying Lamp We are twisting the reflector with the chandelier with short bolts.  Carrying lamp From internal To her part of the chandelier body, we fasten each bolt to a suitable nut.
 Carrying Lamp
 Carrying lamp We screw the incandescent lamp in the carry.
 Carry Lamp
That's it. We check the performance of self-made carrying and begin its immediate operation.

Related news


Congratulations on September 1 to the pupils of the school from teachers, parents, grandparents and grandfathers. Poems, prose, funny pictures and short SMS to the Day of Knowledge-2016
So this is why the fingers wrinkle in the water
Top ten ways to disperse metabolism
Craft Box
Daylight saving time in Ukraine in 2019