DIY Distortion Guitar Pedal

Hi friends, today I will tell about the scheme of a guitar lotion with the effect of distortion. The project is quite simple, I recommend it for beginners in soldering.

Need:

  • Operational Amplifier TL072.
  • Resistor 10 kΩ (4 pcs.)
  • Resistor 1 mΩ (2 pcs).
  • Resistor 3.3 kΩ.
  • Resistor 680 kΩ.
  • Potentiometer 100 kΩ (2 pcs.).
  • Potentiometer 50 kΩ.
  • Capacitor 100 nF (3 pcs.).
  • Capacitor 10 nF.
  • Capacitor 100 uF.
  • Capacitor 47 nF.
  • Capacitor 47 pF.
  • Capacitor 100 pF.
  • Diode 1N4148 (2 pcs).
  • Button.
  • 2 sockets for a 6.1 mm jack.
  • Socket for the crown and crown.
  • All this can be bought in the nearest electronics store. You can also use tweezers and a third hand for soldering for convenience.

    Assembling the circuit

    DIY Distortion Guitar Pedal
    On the Internet, I found a scheme for this project.
    Doing your own Distortion guitar pedal
    But we will not do it on the board, because first we will have to make it, and not everyone knows how to poison the printed circuit boards. This pedal will be as simple as possible. We will assemble it on a 66 * 33 mm carton, and it will be as the main board.It turns out something between a printed circuit board and a mounted installation. On the cardboard glue using PVA layout project. The layout must be printed in real size (as in the photo).
    Guitar pedal Distortion with your own hands
    Guitar pedal Distortion with your own hands
Guitar pedal Distortion with your own handsGuitar pedal Distortion with your own hands Then I sewed holes in the cardboard under the feet of the radio parts for the sewing needle. DIY Distortion Guitar Pedal Cut the legs of the parts in any case can not, they will act as tracks. Now we insert the parts in their places, and on the reverse side we disappear the tracks. We do not have much to say about this, it's all intuitively clear.
Guitar pedal Distortion with your own hands
Guitar pedal Distortion with your own hands In some places their length will be short, so use wires.Like here:
DIY Distortion guitar pedal
When everything is ready, the board will look like this:
DIY Distortion Guitar Pedal
DIY Distortion guitar pedal
Now, according to the scheme I gave earlier, we solder the button, the connector for the crown battery and jacks for jacks.
DIY Distortion Guitar Pedal
DIY Distortion guitar pedal
Places where closure is possible, I taped a hot-melt adhesive.
Do-it-yourself Distortion pedal
This production of the circuit itself is complete.

Body

After a short test, it became clear that the pedal was working. Now we will make for her body. Made out of the box under the sponge for shoes. The collective farm, of course, but the pedal was originally made "cheap and cheerful."
Guitar pedal Distortion with your own hands
In the cover holes for potentiometers and buttons are made. On the sides for jacks. The box was too small.And with the crown it was barely closed, so I had to cover the lid with tape.
Do-it-Yourself Distortion Guitar Pedal
I had a couple of handles for krutilok, but they did not fit here. Therefore, I used a little thing to turn the knobs gain, tone, level. This completes the manufacturing of the Distortion guitar pedal. The project is quite simple, the sound is fine with me.

Related news


Military equipment pictures for children
Drinking coffee: good or bad
Angelina Jolie refuted rumors about the departure of her lawyer
Designer creates very large-knit clothing and accessories
How to choose shoes